Bandai 2003: Difference between revisions

From WSdev Wiki
Jump to navigationJump to search
(→‎2003 RTC interface: floating SIO pin is pulled high)
Line 106: Line 106:


=== $16 ===
=== $16 ===
Send command byte ($66), then send three bytes of payload, then stop.bit.
Send command byte ($66), then send three bytes of payload, then stop.


=== $17 ===
=== $17 ===
Line 112: Line 112:


=== $18, $1A ===
=== $18, $1A ===
Send command byte ($68 or $6A), then send two bytes of payload, then stop.needed" bit.
Send command byte ($68 or $6A), then send two bytes of payload, then stop.


=== $19, $1B ===
=== $19, $1B ===
Send command byte ($69 or $6B), then receive two bytes of payload, then stop.
Send command byte ($69 or $6B), then receive two bytes of payload, then stop.

Revision as of 21:09, 21 August 2023

In addition to the normal Mapper banking interface, Bandai's 2003 adds registers for an RTC interface, GPO pins, self flashing, and accessing more than 16MiB of ROM.

Category Port Description Bits Type Notes
RTC $CA RTC Command ...1 CCCC W8 Command (C)
RTC Status D00B CCCC R8 Busy (B), Command (C), Data needed (D)
$CB RTC Payload dddd dddd RW8 Data (d)
GPO $CC GPO Data Direction 0000 oooo RW8 1 = output, 0 = high-impedance (weak pull-down)
$CD GPO Data 0000 dddd RW8 1 = 3V, if enabled by data direction
Self-Flash $CE Self-Flash Control 0000 000r RW8 1 = ROM is accessible at segment 0x1000;

0 = RAM instead.

Extended bankswitching $CF ROM Linear (EX) Bank 00bb bbbb RW8 Selects a 1MiB bank accessed via segments 0x4000 through 0xF000. Identical to the register at 0xC0.
$D0 RAM(/ROM) Bank 0000 00bb bbbb bbbb RW16 Selects a 64KiB bank accessed via segment 0x1000. Lower 8 bits are identical to the register at 0xC1.
$D2 ROM0 Bank 0000 00bb bbbb bbbb RW16 Selects a 64KiB bank accessed via segment 0x2000. Lower 8 bits are identical to the register at 0xC2.
$D4 ROM1 Bank 0000 00bb bbbb bbbb RW16 Selects a 64KiB bank accessed via segment 0x3000. Lower 8 bits are identical to the register at 0xC3.

Not all PCBs are wired to support self-flashing. Not all ROMs have the needed /BYTE pin. Even on PCBs without support, ROM can still be enabled by writing to port $CE.

2003 RTC interface

The 2003's RTC interface is a simple half-duplex SPI-like protocol. A write to $CA will start a transaction, depending on the exact value written.

If there is no external S-3511A, all bytes will read back as $FF due to a weak pull-up inside the 2003.

For specifics of what the S-3511A expects to be done with these bytes, see Real-Time Clock.

(Put logic analyzer traces here)

Values are as follows:

$00-$0F, $1C-$1F

Immediately stop the transaction. This cannot be safely used to abort an ongoing transaction, because the 2003 still relays the 384kHz clock. In contrast, normal termination stops relaying that clock.

$10, $11

Send command byte ($60 or $61 respectively) and stop.

$12

Send command byte ($62), then send byte stored in $CB, then stop. The 2003 expects that the value in $CB is valid and does not pause if the CPU hasn't yet written a value.

$13

Send command byte ($63), then receive byte, then stop. After the "data needed" is set or the "busy" bit is clear the value can be read from $CB.

$14

Send command byte ($64), then send seven bytes of payload, then stop. The 2003 expects that the first byte is preloaded in $CB, but pauses for the CPU to write each subsequent byte by setting the "Data needed" bit.

$15

Send command byte ($65), then receive seven bytes of payload, then stop. The 2003 pauses for the CPU to read each subsequent byte by setting the "Data needed" bit.

$16

Send command byte ($66), then send three bytes of payload, then stop.

$17

Send command byte ($67), then receive three bytes of payload, then stop.

$18, $1A

Send command byte ($68 or $6A), then send two bytes of payload, then stop.

$19, $1B

Send command byte ($69 or $6B), then receive two bytes of payload, then stop.